What Causes Black Spots on Pavers, and Can They Be Removed?
@johnathanqogi192
November 22, 2026 · 8 min read
If you have noticed dark, speckled patches creeping across your driveway, patio or pool surround, you are not alone. Black spots on pavers are one of the most common complaints among Geelong homeowners. The good news is that in most cases they can be removed, and with the right care they can be kept from returning. This guide explains what causes them, how to identify the culprit, and the best ways to restore your pavers.
Why Geelong Pavers Are Prone to Black Spots
Geelong's coastal climate creates a mix of conditions that organisms and stains love. Cool, damp winters, regular morning dew, sea air and shaded backyards all keep paver surfaces moist for long periods. Pavers are also naturally porous, especially concrete and some natural stone varieties, so moisture, spores and organic debris settle into the surface rather than simply sitting on top.
Areas that stay damp and receive little sun, such as south-facing courtyards, spots under eaves, or paving beneath established trees, tend to show black spotting first.
The Most Common Causes of Black Spots on Pavers
Mould and Mildew
Mould is one of the leading causes of black spotting. Spores land on the paver surface and, when they find moisture and organic matter such as dust, pollen or leaf residue, they begin to grow. Mould typically appears as small, scattered dark specks that can merge into larger patches over time. It often has a fuzzy or powdery look when examined closely.
Algae and Lichen
Algae usually presents as green, but certain types and dried-out colonies look dark brown or black. Lichen, a combination of algae and fungi, forms crusty, tightly bonded patches that can be grey, black or even orange. Lichen grips the surface firmly and is harder to remove than loose mould or algae.

Tree Sap, Leaf Tannins and Organic Debris
Fallen leaves, flowers, berries and sap leave behind tannin stains that look like dark spots. Trees common in Geelong gardens, such as eucalypts, liquidambars and fruit trees, can all contribute. Berries and sticky sap are especially stubborn, because they soak into the pores of the paver as they break down.
Chewing Gum
Old chewing gum that has been trodden on turns dark grey or black and bonds tightly to the surface. It is easily mistaken for a stain, but it is a raised, sticky deposit rather than discolouration within the paver.
Oil, Grease and Vehicle Fluids
Driveways are particularly vulnerable to oil leaks, brake fluid and tyre residue. These typically create dark, irregular spots in parking positions. Because oil penetrates deeply into porous pavers, fresh spills are much easier to treat than old ones.
Rust and Metal Stains
Rust from metal furniture, pot stands, or even fertiliser can cause brown to black staining. Bore water used for irrigation can also deposit iron-based marks, which is worth checking if staining appears near sprinklers.
Efflorescence and Mineral Staining
Efflorescence is usually white and powdery, but moisture trapped in the paver can cause patchy, darker-looking areas, particularly on newly laid pavers. It generally fades over time but can be mistaken for other staining.

How to Identify What You Are Dealing With
Correctly identifying the cause makes removal far more effective, because each type of stain responds to different treatments. Here is a simple way to narrow it down:
- Location: Spots in shaded, damp areas are likely mould, algae or lichen. Spots in car spaces are probably oil. Spots under trees suggest tannin or sap.
- Texture: Raised, hard, round spots are likely chewing gum. Crusty patches that resist scraping suggest lichen. Flat, soaked-in marks suggest oil, rust or tannins.
- Water test: Sprinkle a few drops of water on the stain. If it beads up, oil is likely present. If it soaks in quickly, the stain is probably organic or mineral based.
- Colour: Orange-brown tones point to rust, while green-black or grey-black patches usually indicate biological growth.
Can Black Spots on Pavers Be Removed?
In most cases, yes. Biological growth such as mould, algae and lichen can usually be removed completely. Fresh oil and organic stains also respond well. Older, deeply set stains, particularly oil that has been soaking in for years, may lighten significantly but not always vanish entirely. The sooner you act, the better the result.
Methods for Removing Black Spots
Sweeping and Scrubbing
Start by sweeping away loose dirt and leaf litter. A stiff-bristle broom or brush and a bucket of warm water with a mild detergent will remove light surface staining. Avoid wire brushes on most pavers, as they can scratch or damage the surface.
Pressure Washing
High-pressure cleaning is one of the most effective ways to lift mould, algae, lichen and ingrained dirt. However, pressure that is too high or a nozzle held too close can etch the surface, strip sealer, wash out joint sand and leave stripes. Different paver materials, including concrete, clay, bluestone, travertine and limestone, tolerate different pressures, so it pays to test a small area first or hire a professional who knows how to adjust their equipment.
Biological Treatments and Mould Removers
For mould and algae, a purpose-made outdoor cleaner or a diluted oxygen bleach solution is typically safer for surrounding plants than strong chlorine products. Apply the treatment, allow it to work for the time recommended on the label, then scrub and rinse thoroughly. Always protect nearby garden beds, wet the plants beforehand, and wear gloves and eye protection.
Poultice for Oil and Grease
For oil stains, absorb any fresh spill immediately with cat litter, sawdust or cornflour. For older stains, a poultice made from an absorbent powder and a suitable degreaser can draw oil out of the paver. Leave it to sit, usually for 24 hours, then sweep it away and repeat if needed. Commercial degreasers designed for concrete and pavers also work well.

Rust Removers
Rust stains require a dedicated rust remover, typically oxalic acid based. Do not use chlorine bleach on rust, as it can set the stain. Follow manufacturer instructions carefully and rinse well.
Removing Chewing Gum
Freeze the gum with ice or a freezing spray so it becomes brittle, then gently chip it off with a plastic scraper. Any remaining residue can be treated with a suitable solvent or hot-water pressure cleaning.
What Not to Do
- Avoid using undiluted pool chlorine or harsh acids on pavers without checking suitability. Acid can damage concrete and limestone, causing permanent etching and colour loss.
- Do not use a turbo nozzle or very high pressure on soft or aged pavers.
- Avoid letting chemical runoff enter stormwater drains. In Victoria, stormwater runs untreated to local waterways and the bay, so wash-off should be directed to garden beds or lawn where appropriate, and detergents and chemicals should be used sparingly.
- Do not scrub aggressively on sealed pavers, as it can dull or strip the sealer.
How to Stop Black Spots from Coming Back
Seal Your Pavers
A quality penetrating sealer fills the pores of the paver, making it more resistant to oil, tannins, mould and moisture. Sealing also makes day-to-day cleaning easier. Sealers should be reapplied periodically, often every two to five years depending on product type, traffic and exposure. Always clean and dry pavers thoroughly before sealing, as sealing https://travishgcy107.theglensecret.com/how-to-prepare-your-property-for-a-pressure-cleaning-visit over mould or stains locks them in.
Improve Drainage and Sunlight
Pooling water encourages growth. Check that your paving has an adequate fall so water runs off, and clear gutters and downpipes that might overflow onto paved areas. Where practical, trim back overhanging branches and thin dense plantings to let more sunlight and airflow reach the surface.
Regular Maintenance
Sweep regularly to remove leaves, flowers and debris before they break down. A routine wash every few months, along with an annual deeper clean, can prevent the build-up that leads to staining. Treat spills, especially oil, as soon as they occur.
Keep Joints in Good Condition
Joint sand holds moisture and organic matter, and weeds and moss can take root there. Topping up or replacing polymeric sand after cleaning helps lock out weeds and reduces damp pockets that foster growth.
When to Call a Professional in Geelong
DIY cleaning works well for light staining, but there are situations where professional help is the better option. Consider calling a local paving cleaning or restoration specialist if:
- The black spots cover a large area, such as a full driveway or pool surround.
- Stains have returned after previous cleaning attempts.
- Your pavers are natural stone, which can be sensitive to acids and high pressure.
- The paving has been sealed and you are unsure what product was used.
- You want a long-lasting result with professional-grade cleaning and resealing.
Professionals have access to commercial surface cleaners, appropriate treatments for different paver materials, and sealers that perform well in Geelong's coastal conditions. They can also advise whether staining is purely cosmetic or a sign of an underlying moisture issue.
Final Thoughts
Black spots on pavers are usually caused by mould, algae, lichen, organic matter or oil, and most of them can be removed with the right method. The key is to identify the cause, choose a suitable cleaning approach, and protect the surface afterwards with sealing and regular maintenance. With a bit of attention, your Geelong driveway, patio or outdoor entertaining area can look fresh and clean for years to come.
Geelong Pressure Cleaning Pros
(03) 8657 4277